Thread Check on the Sheet vs the Gage in the Drawer

The sheet calls for a thread check. The gage is still in the drawer. You cross-reference the lot number printed in the top margin to confirm you have the correct paperwork for the 12mm flanged bolts sitting in the wire bin at your left elbow. The work light casts no harsh shadows across the sheet’s printed thread specification line, so you don’t have to squint to parse the callout. You yank open the top left drawer of your bench cabinet to grab the gage set before moving to the next step.

Matched callout verification for this lot

First, confirm every field on the sheet aligns with the physical lot you are testing. Cross-check the part number, lot code, production date, and thread specification line against the label affixed to the wire bin holding the parts. Illustrative example: This lot’s specified thread pitch is 1.75mm, with a class 6H tolerance for the internal thread cut into each bolt’s flange head. If any field does not match, you flag the sheet for routing to the quality lead before proceeding with any testing. You only move forward once all callouts align perfectly, no exceptions. Small discrepancies in part number or lot code can lead to testing the wrong parts entirely, so you take an extra 10 seconds to scan each field twice before moving to the gage check step.

Thread Check on the Sheet vs the Gage in the Drawer
Shop light on a closed folder.

Gage calibration cross-check

Before you handle any parts, verify the gage you pulled from the drawer has a valid calibration sticker affixed to its plastic case. Check the expiration date on the sticker against the date printed at the top of this sheet to confirm the calibration remains active for the duration of this lot check. If the sticker is missing, faded, or expired, you return the gage to the drawer and pull the backup gage stored in the same slot. You note the gage’s serial number in the margin of this sheet before you start testing to create a clear audit trail for anyone reviewing the paperwork later. If you need to locate a replacement calibrated gage, you request one through the request queue at the Traveler Desk. You never use an uncalibrated gage for testing, even if the lot is behind schedule, as uncalibrated tools can produce inaccurate results that lead to rework later in the production process.

Thread testing step-by-step workflow

You follow this exact sequence for every 10-part sample pulled from the lot, per the sheet’s sampling requirements:

  1. Wipe any excess machining oil or metal shavings from both the GO and NO-GO ends of the gage with a lint-free shop cloth, taking care not to scratch the threaded surface of the gage that makes contact with test parts.
  2. Insert the GO end of the gage into the internal thread of the test part, applying steady, even pressure without forcing the gage to turn. The gage should screw fully into the thread with no binding, wobble, or extra resistance that indicates an undersized thread.
  3. Remove the GO end and insert the NO-GO end of the gage into the same thread, applying the same steady, even pressure. The NO-GO end should not turn more than one full rotation before stopping, which confirms the thread is not oversized enough to fail fit requirements during assembly.
  4. Record the result for each test part in the corresponding row of the results table on the lower half of this sheet, marking a “P” for pass and an “F” for fail next to the part’s sequential sample number.
  5. If any part in the 10-part sample fails, you pull an additional 20-part sample from the same lot and repeat the test for every part in the expanded sample to confirm if the failure is an isolated defect or a lot-wide issue that requires further review from the engineering team.

Deviation logging protocol for this document

Any test result that falls outside the specified tolerance gets logged in the deviation section on the back of this sheet, with a full description of the failure pattern, the number of failed parts in the sample, and the serial number of the gage used for testing. You attach a small, labeled sample of any failed parts to the back of the sheet with heavy-duty tape, making sure the sample does not cover any pre-printed text or existing entries on the document. You do not make any erasures or cross out entries on the sheet; if you make a mistake when logging a result, you draw a single thin line through the incorrect entry, initial and date the correction, and write the correct entry next to it. This ensures the full history of the lot check remains visible and traceable for all future reviews, so anyone reviewing the document can see exactly what was tested, what results were recorded, and what corrections were made if any. You also note any environmental factors that may have impacted testing, like extreme cold or humidity in the shop, to give context to results that fall near the edge of the tolerance range.

Sign-off procedure for completed lot checks

Once you finish testing all required samples and logging all results, you print your full name, employee ID number, and the date and time of the completed check in the designated sign-off box on the bottom right corner of the sheet. You double-check that you have filled in every required field, including the gage serial number, sample size, number of passed and failed parts, and any notes about deviations or expanded sampling. You do not leave any required fields blank, even if the test resulted in zero failed parts; you write “0” in the failed parts field to confirm you completed the count and did not overlook the entry. Once signed, you place the sheet in the out tray at the edge of your bench for routing to the quality team for secondary review. The quality team will cross-check 10% of the sample parts you tested to confirm your results align with their own testing before approving the lot for movement to the next production stage.

Next scheduled review of this active lot sheet

You will pull this sheet from the quality team’s approved lot file the next time this lot is scheduled for kitting and assembly, which falls 14 days from the date of this initial check. During that review, you will cross-reference the thread check results logged here against the assembly team’s fit test results for the parts, to confirm no unexpected thread wear or damage occurred during storage in the climate-controlled parts warehouse. You will also verify the gage calibration remains valid for any follow-up testing required during the kitting process, and log any additional notes directly on this sheet following the same deviation and correction protocols used for the initial check. You do not create a new sheet for this follow-up review; all entries tie back to this original document to keep the full lot history consolidated in one place. If the lot passes all kitting and assembly checks, this sheet will be filed in the completed lot archive for a minimum of three years per internal documentation requirements.

About · Contact · Privacy · Disclaimer · Advertising · Terms